Click to Enlarge Image

Additional Images
       
The Americana Collection
BOSTON
  • Translucent White Acrylic Half-Round Diffuser
  • Aluminum Extruded Square 6 Bar Cage
  • Aluminum Perforated Decorative Insert
Download: Boston Spec-Sheet
ADA Americana Spec-Sheet
*Click +/- to expand/collapse information
  Product Specifications:
Driver: Universal Voltage 120 or 277V.

Backbox: 16 gauge aluminum. Wire access through .875" diameter knockouts on four sides and back. Water tight. Optional for surface conduit entry.

Backplate: 16 gauge aluminum

Cage: Standardized .375" or .5" diameter aluminum guard bars secured by hidden means to the frame. Standard square extruded bars. Standard configurations shown; custom spacing available.

Diffuser: Translucent white non-yellowing 100% virgin acrylic. Fully enclosed. Clear top and bottom [CLTB] is Standard with Uplight or/and Downlight. Optional Opaque top, bottom or both [OTB]. Optional Open [OPTB] top and/or bottom — Indoor Only. Optional [PF] perforated aluminum insert. Optional Aluminum Solid Shield Top/Bottom (No Light).

Painted Finish: Pre-treated highly durable oven baked polyester powder finish. Corrosion and Weather resistant. Standard [BK] Black, [BZ] Bronze, [Sv] Silvadillo or [WHT] white. Available Custom Colors [CC] are listed.

Gasketing: High temperature and non-aging neoprene rubber and/or black EPDM completely around the perimeter of the lens and around the rear wire entrance hole. Protects against dust, moisture and outside contamination.

Lens Fasteners: 2 Stainless steel tamperproof screws.

Mounting: Access hole in center for indoor mounting to a J-BOX. For indoor/outdoor use 1/4" Diameter bolts in 4 holes, 5/16" Diameter.

Compliance: Built according to U.S. and Canadian Safety Standards. Suitable for Wet Location.

  Sizes:
Standard Sizes
13 =
8¼" Width x 13¼" Height x 4" Depth (ADA)
16 = 8¼" Width x 16" Height x 5½" Depth
21 = 9¼" Width x 21" Height x 5½" Depth
26 = 12¼" Width x 26¼" Height x 7¼" Depth
41 = 14" Width x 41" Height x 8½" Depth

ADA Sizes
18-ADA =
8¼" Width x 18" Height x 4" Depth
21-ADA = 8¼" Width x 21" Height x 4" Depth
26-ADA = 8¼" Width x 26¼" Height x 4" Depth 
30-ADA = 8¼" Width x 30" Height x 4" Depth

  LED/Size Wattages:
Lamping KEY
LED =
Light Emitting Diode
LU = LED Uplight
LD = LED Downlight

13" LED Wattage
LED =
 15 Watt
LU/LD = 5 Watt

16" Lamps/Wattage
LED = 15 Watt
LU/LD = 5 Watt

21" Lamps/Wattage
LED = 15 Watt / 30 Watt
LU/LD = 5 Watt / 10 Watt

26" Lamps/Wattage
LED = 40 Watt / 60 Watt
LU/LD = 5 Watt / 10 Watt / 25 Watt (Requires CA)

41" Lamps/Wattage
LED = 60 Watt
LU/LD = 5 Watt / 10 Watt / 25 Watt (Requires CA)

*For ADA Lamps/Wattages Refer to:
 ADA American Spec-sheet

  Color Temperature:
CT3 = +/-3000K LED Color Temp
CT4 = +/-4000K LED Color Temp
CT5 = +/-5000K LED Color Temp

  Voltage:
120 = 120 Volts
277 = 277 Volts
347 = 347 Volts
UNV = 120~277 Universal Volt Electronic Driver
2UNV = Two 120~277 Universal Volt Electronic Drivers

  Options:
0-10D = 0-10V Low Voltage LED Dimming
CA = Aluminum Backbox/Surface Conduit [2" deep]
CLTB = Clear Top & Bottom (Standard with LU/LD)
CM = Ceiling Mount (Custom Requirements)
CU = Custom Requirements
EM = Emergency battery (CA required) - Damp Location (Must Specify Voltage [120V or 277V]; Consult Factory for EM Options)
FUS = Fuse and Fuseholder
DFUS = Double Fuse and Fuseholder
GN = Generator Transfer Device
H/L1 = High/Low Light Level for LED
-Single AC-Input Feed / Switch Sensor (Required)
H/L2 = High/Low Light Level for LED
-Wired for Dual AC Input Feeds
HOR = Horizontal Mount (Consult Factory)
MD = Integral Motion Detector
-Specify "A" for Single Circuit: All On / All Off
-Specify "B" for Single Circuit: Half On / Half Off
MDX = External Motion Detector
-Specify "A" for Single Circuit: All On / All Off
-Specify "B" for Single Circuit: Half On / Half Off
-Specify White (WHT) or Bronze (BZ) Finish
OTB = Opaque Top & Bottom
OPTB = Open Top & Bottom (indoor only)
PHT1 = Integral Photocell 120V [CA required]
PHT7 = Integral Photocell 277V [CA required]
PHTD = Integral Photocell Dual Voltage 277V [CA required]
REM = Remote Emergency Battery
self-contained in CA – Must Specify Voltage [120V or 277V];
Consult Factory for REM Options
SSDTB = Aluminum Solid Shield Top / Bottom (No Light)
TPD = Tamperproof Screwdriver

  Painted Finishes:
BK = Black
BZ = Bronze
PA = Painted Aluminum
SV =
Silvadillo Gray
WHT = White
CC = Custom Color [Specify RAL#]